How Do You Lace An Underbust Corset?
1. Begin by loosening the lacing on the back of the corset. Insert your arms through the arm openings and wrap the corset around you so that it sits beneath your bust line.
2. Once in position, begin to pull both ends of laces from each side in an alternating motion starting at your waistline. Pull gently until you reach your desired fit and shape while keeping tension even throughout each side of the corset.
3. Tie a bow or granny knot at either end once finished tying to keep lace tight and secure - be sure not to make them too tight though. Repeat as needed when necessary for more precise adjustments and/or better comfortability throughout wear.
Contents:
Preparing the Garment
Proper preparation of the garment is key to lacing an underbust corset properly. Start by hand-washing the corset with a mild detergent and gentle soap. Dry on a flat surface in the shade, away from direct sunlight, as this can damage the material. When it comes to selecting a thread for stitching your corset, it's best to go with an ultra-durable waxed nylon or polyester thread that won't break easily and is hardy enough to cope with daily wear and tear. If you're not confident sewing by hand, there are plenty of overlockers available at affordable prices that will do most of the work for you automatically - although be warned. Many offer only basic functionality so check what type of stitch each machine produces before buying.
To finish off your creation, trimming the edges using bias binding tape can help reinforce them and provide more security when lacing up your corset. It also looks neat and finished. Alternatively, if you prefer a less structured look some people opt for simple blanket stitch around their garment which works just as well but leaves much softer lines along your seam. Finally remember that whatever method you use always make sure that all raw edges are secure otherwise they may snag when lacing up later on.
Understand the Lacing Pattern
When it comes to lacing an underbust corset, understanding the pattern is key. It’s important to start with an even number of eyelets on each side and begin at the back in order to maintain balance. The first step is to loop the lace end through one eyelet, starting from the bottom up. Make sure both sides are loose before continuing. For a basic cross-lacing pattern, after passing one end of your lace through the opposite eyelet on the opposite side and pulling it tight until snug, you can then proceed with crisscrossing your laces across back and forth between the remaining pairs of eyelets. As you pull each lace tight, take into account that this will affect how securely they fit; adjust accordingly as needed. Once you reach the topmost pair of eyelets, simply tie them off in a knot or bow for secure closure. With practice and patience, you’ll soon be well on your way to creating beautiful yet secure patterns that'll surely turn heads wherever you go.
Fasten Grommets Properly
Fastening your grommets is the most important step of lacing an underbust corset. Grommets are small eyelets located along the edges of the corset, allowing for a sturdy lace or ribbon to be threaded through. If you don't properly secure them, your corset won't be able to withstand much tight lacing and could also cause chafing and discomfort. Luckily, fastening your grommets is relatively easy if you know how it’s done.
Your first step should be to use either a hammer or mallet to press each grommet into its designated spot on the fabric. Make sure that all parts of the metal rings are securely in place on both sides of the garment; this will ensure a proper fit and minimize any irritation from stitching or rough edges of fabric. It's very important that none of the metal elements protrude outward, as this can cause injuries when wearing and tightening your corset.
Once all the grommets have been placed correctly it's time to thread your lace or ribbon through each one in order from top-to-bottom (or bottom-to-top). To do this evenly and effectively, start by tying two ends of your lace together so that there are no knots at either end before passing it through each hole. This ensures that none of the lacing gets stuck in between two sets of eyelets while doing up your corset – making sure everything is pulled tight once finished with minimum effort. With these easy steps, you'll be looking stylishly laced in no time.
Tie a Starting Knot
Most novice corset wearers find tying a knot at the back of their underbust corset to be the most daunting part of wearing the garment. However, with some practice and by following this guide, anyone can learn to tie a knot with ease.
When beginning your corset lacing experience, use a flat starting knot. This is done by threading one end of the lace through the eyelet nearest to your waist and pulling it tight. Then take the two ends of both sides and wrap them around each other twice before passing the near side over and then under itself from right to left. Pull both sides tightly in opposite directions to create a snug fit against your body without any visible bumps on either side.
If you’re unsure how tight or loose you should lace your corset, begin loosely and then gradually tighten as needed for comfort throughout wear. To ensure that everything remains secure when tightening your ties, make sure that after looping around twice that each end crosses over from its own direction towards the other side (i.E. No criss-crossed patterns). You also want to evenly tighten each end until there are no large gaps between each row of eyes when looking down at where your laces meet in front - it should look like two snakes running down either side.
Working from Top to Bottom
When it comes to lacing a corset, many assume they should start from the bottom. However, this may cause strain on the lower laces and limit mobility. The best method is actually to begin at the top of your underbust corset, which will also allow for better tightening and movement as you work down.
Start by taking two of the middle laces and tying them in a simple knot near the top of your corset. Gently pull on each side of the lace until both sides are even in length, creating tension for when you move down towards your waistline. To ensure symmetry, make sure that all four sides remain equal in length throughout this process; if there's an imbalance present at any point during your lacing session, undo some previous steps before continuing further.
Once finished with the first knots at the top of your corset, take one end of a lace and place it behind another set right below it. Then repeat this step going all way down until reaching back up to where you began on either side - making sure not to create any more tight spots while crisscrossing each lace over one another for added stability along the way. After completing this technique across both sets from beginning to end, tie off loose ends near bottom hem and enjoy how well-fitted (and comfortable.) Your new silhouette looks.
Finishing with a Bow
Finishing off an underbust corset can be made easy by tying a bow at the back. This charming feature is simple to achieve and adds extra style to your look.
You will need two lengths of ribbon - one to make the knots with and another that is tied into a bow on top. These should match in colour, or you may choose to mismatch for some contrast. The corset lacing should also be done up snugly so that it doesn’t move about when tugging and pulling the ribbons.
The knot-making ribbon needs to be cut slightly longer than twice the circumference of your waistline so you have enough length to tie multiple loops around the front then secure in the back without any gaps where your skin could slip through. Next, loop this around itself and pull tight before fastening it off with double knots. With this section secured, thread the second ribbon through each eyelet then tie them together in a neat bow above all those gorgeous laces. Make sure not to overtighten, as tying too tightly can feel uncomfortable after some time spent wearing it.
Read also about: Why were corsets made?